2014 FORD FUSION Engine Problems

The transmission failed completely. The vehicle will not engage or shift properly and cannot be driven. The failed transmission is still installed in the vehicle and available for inspection upon request.

Coolant is leaking into the head gasket of the 2014 Ford Fusion Hybrid similar to the other 2014 Ford Fusion cars (they have a recall on them for this issue). Upon calling the nearest Ford dealership, I was told that the recall did not apply to my vehicle, even though the same recall has been made for other 2014 Ford Fusions (just not the hybrid specifically). The safety of the driver and passengers in the car is at risk due to the coolant fluid mixing into the engine oil, eventually causing a blown head gasket and potentially engine failure. This problem was identified within minutes of getting a routine oil change, as coolant was found in the cap of the head gasket. The vehicle has not been inspected by the manufacturer, police, or insurance representatives. There were no warning signs. The car notified me when I needed to change my...

On cold startup, a significant amount of white exhaust is sometimes observed coming out of the tailpipes. The exhaust has a sweet aroma and after checking the coolant levels, it appears that the coolant levels have dropped and the exhaust smoke is being caused by a coolant intrusion into the engine block. No warning lights have been observed and it only happens about half of the time.

I had multiple coolant leaks in the pass and I have to constantly replace the hose about every 2000-3000 miles Also my screen went out in my dashboard causing me to not be able to make any audio changes or station adjustments in my car Lastly whenever I get ready to increase my speed my car jerks back

I was having issues with this vehicle sputtering a bit and the antifreeze was seeming to be disappearing. There were no visible leaks. I took it to the shop to have it looked at. The engine light was on and there was a code for a cylinder 3 misfire. Th mechanic diagnosed the vehicle and, upon removing the spark plugs, noticed they were fouled with what he said was antifreeze in the cylinder (because of the white substance on the electrode end). I saw where there is a recall for the particular engine block that is in this vehicle from 2014 to 2020. When I notified Ford and the NHTSA I was told that my VIN number was not included in the recall. I am confused because I would think that the recall would be for vehicles with this particular block not specific VIN numbers. Please help! I just got...

Vehicle flexplate broke causing loss of power in rush hour traffic. Luckily was able to get to the side of the road without major incident or causing an accident. Broken flexplate also caused damage to transmission and ptu. Was informed this is a common issue wiith this yeat make and model but ford refuses to do anything about it. They would rather wait for some peopke to lose their life befor takiing responsibility. But who cares about peoples lives when you have stockholders to pay and ceo bonuses to hand out. Feel its worth mentioning i had the car at the dealership a couple times for other issues and had asked them about problems i suspected were precursors to this happening. They denied there was even an issue. They they told me the noises were normal and refused to even document my concerns let alone actually physically check the vehicle....

A third party hacked my CPU/Transmission Control System causing malfunction with the engine. The engine randomly would cut off during traffic, and I would need to press gas directly after starting the vehicle to go. My vehicle was fairly new and transmission module should not be ineffective after purchasing my vehicle last July 2023 with less than 80K miles. The notification that makes the vehicle stay in the lane would malfunction randomly notifying me of failure to sensor active crash alert. I also have inability to connect to Ford vehicle app with no reason provided to cut off WiFi connectivity. Please review external IP as I can hear communication of third party observing my way of driving and communication while attempting to drive causing distraction affecting safety of myself, my location placement, and health of the car. Possible CPU/transmission/AC connectivity from July 2023 to Malfunction of vehicle starting 10/2024.

Experiencing repeated coolant leaks. Heating/coolant was repaired last winter. Failed again this winter. Car keeps needing additional coolant added. Will be taking it in on Monday to find out which parts failed this time.

I bought the 2014 Fusion in 2019 used. It had roughly 60 some thousand miles. I had to replace the motor at 94 thousand miles. Now at 131 thousand miles, I am faced with the same issue and need to replace the motor again after only 37 thousand miles. From what the dealer said (Copper Country Ford in Houghton Michigan) both issues have been coolant leaking into the cylinders and killing the motor. The first motor was around $4500.00 and now it is roughly the same $4500.00. So $9000.00 in 4 years!!!!! I called Fo Mo Co and they will do nothing to help. They say there is no recall and or order from NHTSA about this issue. Nor do they have any other programs to help resolve this issue or help pay for the repair. First Motor Replaced August 2020 at 94,000 Second Motor Died December 2024 at 131,000

Car stalls then dies out well starting but engine is still on.

When accelerating from a stopped position, the throttle is staying stuck wide open. Without my foot on the accelerator, the engine still accelerates wide open. Stepping on the brake, doesn't do anything or make it stop. It has now happened 3 times in the last 2 weeks. I was not taking off at a fast speed. I was accelerating at a normal rate.

I've had my Ford Fusion SE ecoboost 1.5, 2014 in for service on 2 separate occasions a day apart for the same reoccurring problems. The first service there was the actions done related to recalls which are consistent with 20S15 A-C and recall 23E03 B. The reasons for my Ford Fusion 1.5 to have been brought to the Premier Ford, Waveland, Ms was as follows: The temperature overheat lamp light was jared, there was 3 leaks from the overheat, there was a Shutter and sounds that came from the engine, (LIMP*)and there was no fuel power through acceleration. There had been moisture located on exhaust before brakedown without having been driven for approximately 10hrs before brakedown. 2ed service was as follows: temperature overheat lamp light jared, no power through fuel to accelerate, and issues starting. LIMP* I had not on this brakedown paid attention to if my Fusion needed water,...

Attachment to last complaint

another attachment!

The contact owns a 2014 Ford Fusion. The contact stated while driving at an undisclosed speed, an unknown warning light illuminated, and the contact noticed a ticking sound coming from the vehicle. The contact stated that the check engine warning light later became illuminated. The vehicle was taken to an independent mechanic where it was diagnosed with engine failure. The contact was advised to take the vehicle to the dealer for assistance. The vehicle was towed to the dealer where it was diagnosed with engine failure. The contact was informed that the engine needed to be replaced. The vehicle was repaired. The manufacturer was made aware of the failure but provided no assistance. The failure mileage was approximately 32,000.

This is a attachment to my last Inquiry.

On [XXX] ford premier out of waveland evaluated my car after I had to have it towed in due to overheating. The high temperature warning notification was lock and wouldn't change to normal after it cooled. I was not fully aware of my car overheating due to no warning other the the temperature overheat warning. A couple of days prior without driving it for 10hrs I noticed a moist to the exhaust pipe. When it broke down the engine had a misfire, a shake, and had not power to the engine to accelerate. There was 3 different puddles of fluids underneath the car. When I had spoke to the service department on this breakdown I made them aware of everything with one of the Mechanics witnessing the shake within the engine. There was a confusion on my part due to the sticker showing a 1.5l and my Insurance showing through...

Complaints 11617112 and 11617127 Thank you for your patience with me!

The contact owns a 2014 Ford Fusion. The contact stated that while adding coolant, the coolant was leaking out. The contact stated that while driving at an undisclosed speed, the vehicle failed to accelerate properly. The vehicle was turned off and restarted and there was smoke detected. The contact opened the hood and noticed that the coolant level was low. The check engine warning light was illuminated. The contact stated that the failure was related to NHTSA Campaign Number: 17V209000 (Engine and Engine Cooling). The vehicle was towed to the local dealer but was not diagnosed or repaired. The manufacturer was contacted and opened a case. The failure mileage was approximately 60,000.

My 2014 ford fusion titanium 2.0 ecoboost engine has Coolant leaks causing engine overheating, missfire on cylender 4, car keeps shuddering and stalling while driving. Contacted ford about this issiue they refused to fix it even though there is a mass recall on the same Caras mie for the same issiues

Vehicle showing signs of coolant leak with no visible of signs of coolant on ground. Check engine light came on and running rough on startup and high speeds. White smoke and sputtering under load. Took to local mechanic and had signs of coolant in #3 cylinder. Replaced all spark plugs and ignition coils along with thermostat and pressure tested. Vehicle still throwing codes and having heavy misfires in #3 cylinder with coolant loss. Stated will need a new long block. Vin number not covered by recall. But Def needs to be.

The contact owns a 2014 Ford Fusion. The contact stated while driving at an undisclosed speed, there was white smoke coming from the exhaust, and the check engine warning light was illuminated. The contact also stated that the vehicle was consuming an excessive amount of coolant; however, there were no visual coolant leaks found. The vehicle was towed to two independent mechanics for confirmation, where the vehicle was diagnosed with a coolant leak and a blown head gasket. The contact was informed that the engine needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure. The contact was informed that the repair was not eligible for coverage under the Technical Service Bulletin: 20-2100. The contact was advised to contact the NHTSA Hotline to report the failure. The failure mileage was approximately 111,000.

The contact owns a 2014 Ford Fusion. The contact stated while driving at an undisclosed speed, the exhaust pipes of the vehicle would abnormally blow white smoke. The check engine temperature warning light had been illuminated. The vehicle was taken to a local dealer where it was diagnosed that the engine needed to be replaced. The vehicle was not repaired. The vehicle was then taken to an independent mechanic for a second opinion where it was diagnosed that there was a coolant intrusion. The contact was informed of TSB: 22-2322. The manufacturer was made aware of the failure. The failure mileage was approximately 140,000.

The contact owns a 2014 Ford Fusion. The contact stated that the vehicle was taken to the dealer to be serviced. The contact stated while picking up the vehicle, the check engine warning light was illuminated. The dealer was notified of the failure. The dealer diagnosed that the O2 sensors had failed and informed the contact that a fee would be charged for the repairs. The vehicle was not repaired. The manufacturer was notified of the failure and a case was opened. The failure mileage was approximately 132,819.

Coolant intrusion - engine needs to be replaced.

The contact owns a 2014 Ford Fusion. The contact stated while driving at an undisclosed speed, the oil pressure warning light illuminated, and the vehicle lost motive power. There was smoke coming from the exhaust pipe, and upon inspection, the exhaust pipe was wet. The contact checked the engine oil level and added water to the coolant reservoir. The vehicle was restarted and was driven to the residence. The failure recurred, and the vehicle coasted into the driveway. The vehicle was diagnosed by an independent mechanic at the residence, and it was determined there was a blown head gasket and coolant intrusion into the engine. The contact was informed that the engine needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure and advised the contact to file a complaint with the NHTSA Hotline. The failure mileage was approximately 209,000.

I own a 2014 Ford Fusion. While driving at a slow speed, the "Engine Coolant Overtemperature" warning light illuminated. The vehicle was taken to a dealer where the water pump, thermostat, a/c hoses was replaced; however, several days later while driving 65 MPH, the "Engine Coolant Overtemperature" warning light illuminated, and the vehicle stalled. Due to the failure, the vehicle has been towed back twice to the dealer where the mechanic discovered a coolant intrusion into an engine cylinder. The mechanic informed me that the engine needed to be replaced. The vehicle was not repaired. The failure mileage 69k

In January 2024, while driving the Ford Fusion, I lost power (when I pressed the gas, it would accelerate). I pulled over the best I could (on a 2 lane road, no shoulder, at night). I found that my vehicle had no coolant; it had an oil change within the last 2 months and all fluids were topped off. It was towed to my mechanic and I had to call family for a ride. It was found that the coolant had leaked and burned out, thereby overheating, warping the block/head (placing it in limp mode). It was not holding compression or fluid. For a new engine and installation, I paid $6,800.67. Tonight ([XXX]) my "check manual" wrench light came on and I pulled over to find the coolant was near empty. I was an hour away from home, at night, with my younger brother in the car, in Reno, NV....

Engine light came on and coolant temp started to go up and down. Made it home, and started it before worm, started emitting white smoke and had it towed to a dealer. Was told by Ford there was coolant intrusion into cylinder 3 and 4. Was informed this was a common problem by the dealership.

The contact owns a 2014 Ford Fusion. The contact stated that while her husband was driving at an undisclosed speed, the temperature gauge indicated that the engine was overheating; after which, the vehicle lost motive power. The driver was able to pull to the shoulder of the roadway, where the failure persisted. The vehicle was taken to an independent mechanic, who determined that coolant intrusion in cylinder #4 resulted in damages to the engine. The contact was informed that the engine needed to be replaced. The vehicle was not repaired. After investigating the failure, the contact related the failure to Customer Satisfaction Program: 21N12. The manufacturer was notified of the failure, a case was opened, and the contact was referred to the NHTSA Hotline for assistance. The failure mileage was 89,000.

Coolant began leaking into the engine causing engine failure

Car was purchased with less than 100,000k miles and within 2 weeks the the car was put into the shop for loss of power while driving and overheating. Had supposedly needed repair and within a week the car overheated again. Paid over 2,000 in repairs and tows due to issue. Car is towed to Ford was told coolant was in the entire and would need to be replaced over $7000. No way Ford should be able to sell calls with known issues and the consumer be responsible for outrageous repair fees. Ford customer service at corporate nor did the dealership offer any type of assistance with the exception of pay for it or start over for scratch which is impossible with today’s inflation. Ford knowingly sold a faulty product and they should be held accountable.

Vehicle started indicating issues turning over to crank. I purchased a new key and key fob for the vehicle and got it programmed successfully I also replaced the starter with a brand new starter, issue still present in which vehicle is not turning on when I turn vehicle on to crank.

2014 Ford Fusion 1.5 Eco boost engine now has 37,000 miles coolant leak into cylinders. Coolant container empty's quickly. Car is undrivable over heats causing a problem driving on the highway. Two mechanics confirmed.

The contact owns a 2014 Ford Fusion. The contact stated that while operating the vehicle, there was white smoke coming from the exhaust pipes and the engine was misfiring. Additionally, the check engine warning light had remained illuminated. The vehicle was taken to the local dealer who diagnosed that engine coolant had leaked into the engine cylinders and the engine needed to be replaced. The vehicle was not yet repaired. The manufacturer was notified of the failure and the contact was informed that the VIN was not eligible for the Manufacturer’s Extended Coverage for the failure. The failure mileage was 75,000.

The contact owns a 2014 Ford Fusion. The contact stated while pulling out of a parking space and driving, the vehicle jerked and stalled. There was no warning light illuminated. The contact was able to pull to the side of the road. The contact turned off and restarted the vehicle, and the vehicle responded as needed. The contact stated that the failure recurred while driving on another occasion. The vehicle was taken to the dealer however, the failure could not be duplicated. The vehicle was not diagnosed or repaired. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 88,000.

The contact owns a 2014 Ford Fusion. The contact initially discovered that the engine was consuming an excessive amount of coolant. There was no warning light illuminated. Upon inspection, the contact discovered that the coolant level was low; however, the contact later discovered that the coolant level was low again soon after topping off the coolant reservoir. The contact stated that the check engine warning light was illuminated. Upon inspection, the contact discovered that coolant was leaking into an engine cylinder. The dealer was notified of the failure and was given an estimate for a diagnostic test. The manufacturer was notified of the failure and referred the contact to the NTHSA Hotline. The vehicle was not repaired. The failure mileage was approximately 108,000.

Engine coolant leak.

Head gasket failed in January of 2023, replaced water pump timing belt and had a full head job completed. Head gasket failed again in September 2023; had a full head job replacement and now again, my engine has overheated with a suspected blown head gasket.

Coolant intrusion 1.5 liter eco boost.

Coolant leak into the cylinders of the 1.5 L GTDI EcoBoost engine and causes the vehicles to misfire, overheat and even catch fire. As a result of the failure which has been confirmed by an independent mechanic, the car is not operational only has 103K miles.

The contact owns a 2014 Ford Fusion. The contact stated while driving approximately 65 MPH, the vehicle lost motive power. The vehicle failed to function in fifth and sixth gear. There was an abnormal clicking and grinding sound while in fourth gear. There were no warning lights illuminated. The driver was able to pull over to the side of the road. The vehicle was towed to the residence. The vehicle was taken to several independent mechanics, and the contact was informed the vehicle could not be serviced at their location. The local dealer was not contacted. The vehicle was not diagnosed or repaired. The manufacturer was contacted and referred the contact to the NHTSA Hotline. The failure mileage was approximately 146,000.

Large volume coolant leak

Replace my first engine because of overheating and severely white smoke due to leaking coolant. Now I'm about to replace my engine again, same problems. I found out from dealership this problem is on recall , just not my particular car but it's the same motor on the other approved cars.

The contact owns a 2014 Ford Fusion. The contact stated that while his wife was driving at an undisclosed speed, the "Engine Coolant Overheating" message was displayed, and the check engine warning light was illuminated. The contact who is an independent mechanic, diagnosed the vehicle and determined that there was a misfire in the engine and the coolant level was low. The contact added more coolant; however, the failure recurred. The vehicle was not repaired. The manufacturer was made aware of the failure. The failure mileage was approximately 175,000.

Hello, on Saturday May 27th, I took my car in for a regular oil change and thereafter, the rattling noise started the next day, continued rattle had me bring the vehicle back to the dealership on Monday, June 5th. I was informed that my fusion rattling sound was due to the engine flexplate being cracked causing damaging to the transmission oil pump and torque converter. Used chassis ears to pinpoint noise within the transmission bellhousing. Engine flexplat cracked causing out ot round rotation and damage to the transmission. Required transmission and engine flexpalate replacement with alignment due to subframe removal. I looked up online for recalls and found a Ford Customer Satisfaction Program 22N12 for 2019-2020 Fusion - Rattle Noise at the Transmission Bellhousing Area - Flexplate Cracks (dated 08-26-22). Here is the link to the online document found: https://static.nhtsa.gov/odi/tsbs/2022/MC-10218899-0001.pdf. I purchased this vehicle used in 2021. If this issue...

The contact owns a 2014 Ford Fusion. The contact stated while driving approximately 55 MPH, she heard an alarm sound indicating that the coolant temperature warning light was illuminated. The contact stated that she veered the vehicle off the road when the vehicle hesitated, and the engine seized. The contact was unable to restart the vehicle. The contact then notified her husband who advised her to have the vehicle towed. The vehicle was towed to the dealer where it was diagnosed that the engine short block failed and needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure and the contact was informed that the vehicle was over the warranty coverage, but no further assistance was provided. The failure mileage was approximately 50,000.

Codes P0300 P0301 P0316 - My son was driving and approached a red light - his car began to idle rough and check engine light came on. Instructed him to park the car and we towed to a local mechanic. Cylinder 1 was misfiring and also had a mix of oil, fuel and possibly coolant in Cylinder 1. Apparently this is a defective issue with a 2014 Ford Fusion with a 2.0 Ecoboost Engine and also lawsuits regarding this. Ford dealership confirmed this is a sore issue with Ford and referred to Ford Customer Service --- no assistance and just advised to hold onto receipts in case it is a recall issue -- this is not okay at all. Ford has had plenty of opportunities to correct this with Ford Fusions but still have not!!!!! Very very very upset!!!

Engine coolant over temperature light came on as I was pulling in my driveway. Checked the coolant, it was very low. There’s been no visible leaks on the driveway. Added coolant, turned the vehicle on but the car barely turned over. It’s not drivable. Will need to be towed to the dealer. By all the research I have done, this is a huge issue on this year, make and model with the eco boost engine. This needs to be on the recall program.

My Fusion stalled when exiting a parking lot in a busy downtown area when my 17-year-old son was driving. It restarted and he was able to drive home. After the initial incident, for several days the car sputtered repeatedly. Upon inspection, the Ford dealership indicated the car has coolant leaking into a cylinder causing the performance issues. The Ford dealer service agent indicated I needed a new engine because of the situation. This is just not right. This issue should have been addressed by Ford the right way (when they knew of the design flaw), rather than pushing the problem to its customers, putting their lives and safety at risk.