2020 FORD FUSION Power Train Problems

I am the second owner on my Ford fusion 2020 SE all-wheel-drive I got the car at 21,000 I had warranty since I had the warranty. I've been going for this power training code and having them check my car out all the time they always say there's nothing wrong with it. It's just the code is being erased so by the time my warranty went out all these problems are coming up and now they could find those problems I've been inquiring about

In early October 2025, the vehicle was taken to an independent dealership service department for a routine oil change. Several weeks later, the vehicle appeared to be leaking fluid and began experiencing loud knocking/clacking noises, significant vibration, and drivability concerns, especially during acceleration. On October 10, 2025, while parked at a family member’s residence, the vehicle would not start. Due to safety concerns, the servicing dealership arranged for the vehicle to be towed for inspection. Technicians found a split transmission hose causing transmission fluid loss, which was repaired; however, the abnormal noises, vibration, and drivability issues persisted. Further inspection identified loud popping/clacking noises from the bell housing area. The technician physically inspected the flex plate and documented that the flex plate was cracked. The dealership advised that a cracked flex plate can worsen, cause severe vibration, damage related components, and lead to drivability issues or potential loss of propulsion. Because...

When these problems started it was only 6 months after purchase and I was already having issues with power train malfunctions and it didnt want to switch gears. I purchased this at roughly 47,000 miles and it didnt make it to 70,000 miles before I ultimately decided it was not the safe vehicle that was advertised to my family and I. It was taken to the dealership over 3 times in under a year and for some reason the problem never got resolved. I have been sued for the remaining balance now despite that toward the end of my time owning it the vehicle was reving out with barely any pressure on the gas pedal, having issues braking on its own (anti-collision assist), and occasionally the steering wheel would jerk me in to oncoming traffic. I am just trying to get a recall issued at this point because this car...

My Ford started making a loud noise whenever the accelerator wasn't being pressed, after taking it to the mechanic, he said it is the cracked flex plate. After some light research, it was aparent that this is an issue that Ford's cars have, and ford has tried to make it better by offering free fixes. I contacted the local ford dealer and since the car has 90,000 miles, it would have been covered. However, since it doesn't have a clean title, I was declined this service free of charge. I don't agree with this decision since I've been driving this car for over a year since it was purchased off IAA auction, and this issue was made clear only yesterday, but this issue is prevalent in cars like mine.The damage to my car specifically was to the back, and only affected the rear bumper and trunk. Therefore I don't think...

2020 Ford Fusion SE- Transmission problems. Only 98,000 miles on the car and have had issues with this transmission after a year of having it. Transmission fluid was good but there is a small leak, slipping gears, winding, and gear auto shifting back to park. No combustion or power until it hits 60 mph. Has been checked by mechanics. No lights on dash at all!

VIN: [XXX] Issue Category: Powertrain / Flex Plate / Transmission Failure Dealerships Involved: Freeway Ford – Bloomington, MN J.C. Lewis Ford – Savannah, GA Summary: I am requesting reimbursement from Ford Motor Company for repeated flex plate repairs and a resulting transmission failure on my 2020 Ford Fusion. The vehicle has had five flex plate replacements — three at Freeway Ford in Bloomington, MN, and two at J.C. Lewis Ford in Savannah, GA. Despite all repairs being performed by Ford dealerships, the issue persisted, and the transmission ultimately failed. I was required to pay for a new transmission out of pocket, even though the repeated flex plate failures clearly caused the damage. Ford has a Customer Satisfaction Program (CSP 22N12) addressing flex plate issues on this model, but I received no reimbursement or coverage. I contacted Ford via email to [email protected] with documentation but received no response. I have copies...

This makes the third time the transmission had to be redone and I have only 95.000 miles on it the first time was about 2months after I purchased the car brand new in December 2020 and each time the transmission gets repaired it cost more and more and they tell me that it need other stuff with it that needs to be replaced nothing in the dash showed failure to any thing

The contact owns a 2020 Ford Fusion. The contact stated that upon starting the vehicle, there was an abnormal rattling coming from the vehicle. There was no warning light illuminated. The contact stated that while driving at 20 MPH, the vehicle lost automotive power. There was no warning light illuminated. The vehicle was taken to a local dealer where it was diagnosed, and the contact was informed that the flywheel was faulty and needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure. The approximate failure mileage was 123,000.

My 2020 Ford Fusion has experienced three separate flexplate failures, as well as transmission issues following the most recent repair. Failure #1: Occurred before I owned the vehicle (confirmed later in the vehicle’s history). The flexplate was replaced by a prior owner in 2022. Failure #2: [8/2023] – While I owned the vehicle, a loud rattling noise came from the engine area. My vehicle was towed to Foothill Ford, where it was purchased, and they replaced the flexplate. No power loss occurred. Failure #3: [5/2025] – The same rattling sound returned. I drove it to Green Ford, who confirmed the flexplate needed to be replaced, and they replaced it. No power loss occurred, but the noise was severe. After the third flexplate replacement, the transmission began slipping during acceleration. This issue did not exist before the repair, and Green Ford had told me the transmission was fine before they replaced...

The flexplate in my 2020 Ford Fusion SE (1.5L EcoBoost engine) failed at just over 53,000 miles. The car began making loud knocking and rattling noises while driving, and it vibrated heavily at idle and during acceleration. This posed a serious safety concern, as we feared the car could stall or break down while on the road with our toddler in the backseat. We took it to an independent, certified repair shop where they diagnosed a broken transmission flexplate, which required immediate replacement. The repair cost nearly $3,000, and the shop confirmed it was not caused by driver error or normal wear-and-tear. The failure was premature and mechanical in nature. The mechanic informed us that this specific engine and flexplate design have been recalled before in other Ford models using the same 1.5L EcoBoost engine and parts. They suggested we contact Ford, as this appeared to be a known defect...

The contact owns a 2020 Ford Fusion. The contact stated that while driving at various speeds or while the vehicle was idling, there was an abnormal clunking sound coming from the vehicle. There were no warning lights illuminated. The vehicle was taken to the local dealer where it was diagnosed and determined that the flex plate had fractured. The vehicle was repaired; however, the failure recurred. The manufacturer was not contacted. The failure mileage was approximately 25,000.

I purchased a used 2020 Ford Fusion from Carmax n 2023 with about 56,800 miles. A week later was involved in a nor side impact accident on the back end driver side, insurance paid for a dinted door and there was no other issues with the vehicle according to SONS ford. In 2024 I was on the highway (going about 80 mph) when my engine light came on, no more than 3 minutes later all the lights in my car flickered and i lost power to my entire car almost causing me my life, roadside assistance and a mechanic who had thankfully pulled over explained that my alternator completely shredded my belt. I paid for both my alternator and belt to be replaced But most recently (2025) I continued to whirring and knocking noises for 3 days (no warning lights) , I took it to firestone who stated I needed...

My car is at 47,000 miles and i started To hear a loud noise . Turns out ford says it’s the Flywheel, transmission pump, and torque converter per ford technician who completed my inspection . No warning lights came on nor was there any alerts the ford app. My 2020 Ford Fusion with approximately 48,000 miles experienced a cracked flexplate. This caused severe engine vibration, knocking sounds, and ultimately loss of power while driving. A cracked flexplate can lead to sudden engine stalling or failure to accelerate, especially at highway speeds or during intersections. This puts the driver and passengers at serious risk of a crash due to unexpected loss of power or control. This issue happened without warning and is a known problem in vehicles with the 2.0L EcoBoost engine and 6F35 transmission. Ford is aware of the issue (Customer Satisfaction Program 22N12), but my VIN was not included,...

The contact owns a 2020 Ford Fusion. The contact stated that while driving 35 MPH and attempting to pull into a store parking lot, there was an abnormal whining sound coming from the vehicle. The contact stated that when the gear shifter was shifted to park or neutral, the sound ceased. The contact stated that the sound returned while shifted into drive or reverse. There were no warning lights illuminated. The vehicle was taken to the local dealer in where it was diagnosed and determined that the transmission needed to be replaced. The vehicle was not repaired. The manufacturer was contacted and referred the contact to the NHTSA Hotline. The failure mileage was approximately 65,000.

The contact owns a 2020 Ford Fusion. The contact stated that while driving at various speeds, the vehicle was driving rough. The contact stated that the vehicle hesitated while accelerating with a whining sound coming from the transmission. The cause of the failure was not yet determined. The local mechanic was notified of the failure and informed the contact that the transmission was faulty and needed to be replaced. The manufacturer was contacted and informed of the failure; however, no assistance was provided. The local dealer was not contacted. The failure mileage was 100,000.

The contact owns a 2020 Ford Fusion. The contact stated that upon starting the vehicle, there was an abnormal rattling sound coming from the engine compartment. No warning lights were illuminated. The vehicle was taken to the dealer, who diagnosed a failure with the crankshaft flex plate. The vehicle was not repaired. After investigating the failure, the contact related the failure to Customer Satisfaction Program: 22N12. The manufacturer was notified of the failure, a case was opened, and the contact was referred to the NHTSA Hotline for assistance. The failure mileage was 71,000.

The contact owns a 2020 Ford Fusion. The contact stated that after starting the vehicle there was an abnormally loud knocking sound coming from the engine compartment. The vehicle was taken to the local dealer who diagnosed that the flex plate was cracked and needed to be replaced along with the torque converter, the transmission fluid pump, and seals. The vehicle was repaired. The manufacturer was notified of the failure and informed the contact that the vehicle was no longer eligible for a Customer Satisfaction Campaign related to the failure. The failure mileage was 122,000.

The contact owns a 2020 Ford Fusion. The contact stated that while reversing from the residence, the vehicle suddenly stopped and shifted into park. The contact shifted to reverse, but the gear shifter independently shifted back to park. The contact stated that the vehicle failed to shift to the intended gear. The transmission shifter and the see the owner’s manual messages were displayed. There was a WRENCH symbol displayed. The contact stated that the failure was related to NHTSA Campaign Number: 22V413000 (Power Train); however, the VIN was not included. The contact called the local dealer, who confirmed that there were no recalls on the VIN. The vehicle was not diagnosed or repaired. The manufacturer was contacted and referred the contact to the NHTSA Hotline, but no additional assistance was provided. The failure mileage was approximately 79,127.

Component or system that failed: Flex plate, engine electrical system, and alternator (possible related failures). The issue has been diagnosed by a licensed mechanic and is available for inspection upon request. Incident Description: On April 15, 2025, while driving my 2020 Ford Fusion SE 1.5L Turbo, the vehicle suddenly experienced a total power failure. The check engine light began flashing, and the battery light blinked rapidly. Within seconds, the engine shut down completely while I was mid-drive in traffic, leaving me stuck and unable to move for over 20 seconds. This was a terrifying and dangerous situation that nearly put my life at risk. I was eventually able to restart the vehicle, but it began shaking and rumbling violently — worse than ever before. This issue was never present before my car was involved in two separate collisions, where both other drivers were found 100% at fault. The vehicle was...

My flex plate is cracked making the car unsafe to drive there are recalls on other years and vehicles with the same engine and power train and same flex plate as mine but my vin# says no recall I find it interesting that they can justify not replacing a known faulty part. The campaign 22N12 covers other 2020 ford fusions

The contact owns a 2020 Ford Fusion. The contact stated that while driving at approximately 40 MPH, there was an abnormal rattling sound coming from the engine compartment. The contact stated that the sound was more evident while the vehicle was idling. The vehicle was taken to an independent mechanic and was diagnosed with a fractured flex plate. The contact was informed that the flex plate needed to be replaced. The vehicle was not repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 63,000.

My vehicle was in service with my dealer for several months 3 separate occasions for powertrain issues which werent resolved and now the alignment in my steering wheel is really off. My spouse and I believe the PCM is messed up but have had no progress with our dealership and suspect them of committing consumer fraud and selling us a lemon. The vehicle in question is around 70,000 and started messing up at 60,000.

Began to hear loud rattling noise under hood. Brought to Ford dealer who determined the cause is a failed Flex Plate. Car is operable but was warned this could result in catastrophic failure of the transmission. Vehicle has approximately 62,000 miles, just 2,000 miles out of warranty. Ford Customer Satisfaction Program 22N12 address the issue with an extended warranty for certain model variants (Vehicles Equipped with a 2.0L EcoBoost Engine and 6F35 Transmission). My vehicle has suffered the same failure but has a 1.5L engine so has been excluded.

The steering cable is connected to the transmission hub, and the fitting that connects the two has a gasket that wears away and falls out. This is a recall with vehicles that are made from one of the two plants that assemble fusions, however my vehicle is not covered under the recall even though it is the very same issue as the recall from the other plant. it makes no sense, why is one assembly plant offering a recall for this issue while the other does not? For the same issue of the steering cable coming off the transmission, and not allowing the vehicle to go into gear. I have had to fix this car on the side of the highway before, it will not go into gear on the road. This is not safe at all. You cannot have vehicles just not going into gear while your driving down...

Hard shifting when accelerating/decerating, jerking of the car due to transmission issues (80k miles), ABS/Braking issues due to engine components not being in sync, etc

Car shifts into 1st gear when traveling at higher speeds (45+mph), causing a significant jerk and almost causing a rear end collision to myself. Car also loses power and jerks significantly hardwhen shifting to reverse and drive from Park. Afraid to travel over 45mph due to the downshifting.

The contact owns a 2020 Ford Fusion. The contact stated that the fuel door would randomly disconnect from the vehicle. While idling at a stop light, the vehicle shut off. The contact stated that while restarting the vehicle the vehicle jerked and hesitated while shifting gear before accelerating. The vehicle was taken to the dealer who was unable to determine the cause of the failure because there was no warning light illuminated. The fuel door had been replaced; however, the vehicle still experienced the failure with the START/STOP function. The contact stated that the failure became a persistent failure. The contact stated that approximately 6 to 8 months after the first failure, while driving approximately 35-45 MPH, the vehicle stalled. The contact used the App to restart the vehicle. The check engine warning light was illuminated. The vehicle was returned to the dealer however, the cause of the failure could...

On Saturday, October 5th, 2024, at around 5AM I was sitting in the Starbucks parking lot outside of the Detroit Metro (DTW) airport when this issue began. I had just started my car and could feel it was sluggish and was making a significant amount of noise, which was present in park and neutral, but not so much while in gear, unless I was stopped at a stop sign or stationary. After getting home, and each day after when I started the vehicle to go to work, I could hear that the noise was progressively getting worse. So, I determined that it was not a fluke and took my car into a Ford dealership to have the oil changed and a full inspection done. They explained to me that the water pump had failed and was leaking, very slowly, but externally through the "weep hole". They were going to charge...

On [XXX] I backed my 2020 Ford Fusion out of my driveway. I stopped and tried to shift from reverse to drive and the transmission locked up in Park, the engine died and the parking brake was engaged. I was sitting across the street with no way to move the car. I had the car towed to a Ford dealer and they replaced the transmission cable bushing and cover. These parts are the same as those used in Fords recall 22S43. Ford continued to use inferior parts on cars built after the dates mentioned in the recall. This is a safety issue as it could happen at any time. Thanks [XXX] [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

Flex plate is cracked , confirmed by bore scope dealership is quoting 14 business days to diagnose. It is known issue with this make, model, and year and CSP was issued for dealerships to fix but only select VIN numbers. This car is at 91000 miles and meets all criteria for the CSP 22N12. The car makes an ungodly rattling sound and if it fails could be very dangerous

The engine is “eating” the coolant causing the vehicle to overheat and break down.

The contact owns a 2020 Ford Fusion. The contact stated while operating the vehicle, there was a loud knocking sound coming from the engine compartment and the battery had failed. The vehicle was taken to the local dealer who diagnosed that the transmission flex plate had failed. The vehicle was not repaired. The manufacturer was notified of the failure, but no assistance was offered. The failure mileage was 102,864.

The contact owns a 2020 Ford Fusion. The contact stated that while starting the vehicle, there was a rattling noise coming from the front end near the driver’s side close to the transmission. The vehicle would start moments after the failure had occurred. The rattling was more pronounced while the A/C system was running. The contact stated that while depressing the accelerator pedal, the rattling sound was noticeable. Additionally, while driving at various speeds, the transmission felt as though it was slipping while changing gear. The contact stated that while inspecting the engine, underneath the hood was hotter than normal. The check engine warning light was illuminated. The vehicle had been taken to the dealer where it was diagnosed that the transmission flex plate had failed. The failure was linked to NHTSA Campaign Number: 10218899 (Power Train). The vehicle had not been repaired. The manufacturer was made aware of the...

Cracked flexplate

Rattling and lost of power

The contact owns a 2020 Ford Fusion. The contact stated while starting the vehicle, the vehicle made an abnormal rattling sound. The contact stated that the failure had been recurring. The vehicle was taken to an independent mechanic, where it was diagnosed that there was a rattling sound coming from the transmission bell housing area, and the flex plate was cracked. The vehicle was not repaired. The manufacturer was notified of the failure and informed the contact that the failure was related to Ford Campaign Number: 22N12. The manufacturer assisted the contact in scheduling an appointment with the dealer for diagnostic testing. The manufacturer also referred the contact to the NHTSA Hotline for assistance. The vehicle was not repaired. The failure mileage was approximately 95,755.

The contact owns a 2020 Ford Fusion. The contact stated that while driving at an undisclosed speed, the vehicle failed to accelerate as intended. The contact stated that the vehicle was shaking, and the vehicle lost motive power. In addition, the contact heard an abnormal rattling sound, and the transmission was slipping. The vehicle was taken to the dealer and the contact was advised to flush the transmission fluid. The contact stated that after flushing the transmission fluid, the failure ceased but later returned. The vehicle was not diagnosed or repaired by an independent mechanic or the dealer. The contact stated that after researching the failure, the contact discovered TSB: 22N12. The contact informed the dealer of TSB: 22N12 and the contact was informed that the repair was not eligible to be covered under TSB: 22N12. The vehicle was not diagnosed or repaired by an independent mechanic or the dealer....

The vehicle has 87390 miles and the shifter grommet broke just like recall 19s16. 2020 fustion with a 1.5l engine.

The flexplate was cracking and rusted which caused starting and acceleration problems. Yes, it's available per request. It's currently with the transmission shop that fixed my vehicle. There was a rattling noise found in neutral and park by the transmission shop I took it to. My safety was put at risk because my ability to control my car's power was affected. I was at risk of a loss of power to the wheels which could have caused a major accident, especially because most of my driving happens on the interstate at speeds of 65-7 mph. The issue has been confirmed by an independent service center. Yes, they inspected by the techs at the transmission shop. There were no warning lamps or messages before the failure. The symptoms were a rattling noise and reduced power. This issue is well documented online and is known to happen in the 60-90k mile range...

The flex plate is bad and ford won’t fix it. It needs recalled before it kills someone. Flex plate is the plate that puts power from engine to transmission

Car has the same 6f35 transmission issues as previous years and nothing is being done about it my car has 63k on it with a dead transmission because of the flexplate issue from previous years

The contact owns a 2020 Ford Fusion. The contact stated while driving 30-35 MPH, the vehicle made an abnormal rattling sound. There was no warning light illuminated. The contact was able to continue driving. The contact stated that the vehicle failed to start the following day and was parked. The vehicle was towed to the dealer, where it was diagnosed that the flywheel had failed and needed to be replaced. The dealer informed the contact that the vehicle could not be repaired under Ford Campaign Number: 22N12 because the campaign had exceeded the required mileage. The vehicle was not repaired. The manufacturer was notified of the failure, but no assistance was provided. The failure mileage was approximately 120,251.

At first the check engine light was on and the car would not start. The dash would display all the lights and at one point it turned off while driving luckily I was going 20-30mph. Took it to the dealership and they said an Intake Valve had to be replaced and it was covered by the warranty. Next the engine light was on and a MAP censor had to be replaced which wasn’t covered. Once again the engine light and service light came on and the code is saying the same censor needs to be replaced. Each time it has effected how the car drives and is dangerous especially on the interstate because it will not go over 20mph. When the car is in reverse it will shake and turn off displaying auto start stop issue and place the car in park. It will then turn off. It is hit...

2020 Fusion Compressor one, delivered from factory went out-repaired Compressor 2 just went out Needs 3rd compressor now in 3 years or 38,000-Pending I was very concerned each time the compressor went out (x2) I was on the highway when it ceased up and I lost the ability to effectively control the vehicle. I was put in an unsafe position with the ceasing up and with excessive heat buildup with smelling burning. This was very scary and was unsafe and this part should be investigated for potential to cause harm and injury to those in the car should it happen to anyone else. Limited control of car, notice no more Belt as well after i was able to stop. It appaired to in tiny pieces as small as bee bees all over the car. Not even recognizable as a belt. This has happed 2 times (this is not normal in...

Tapping / knocking coming from the driver side of the engine bay . Slow engagement now knocking while parked and in gear ...was told it was the transmission which is a known issue for this car now my car won't move ... Wondering why this year model and setup has not been recalled

The contact owns a 2020 Ford Fusion. The contact stated while exiting a parking lot, the contact heard an abnormal sound coming from the vehicle. The contact stated that the vehicle failed to accelerate as needed. There was no warning light illuminated. The vehicle was towed to the dealer and the contact was informed that the transmission needed to be replaced. The contact was referred to the manufacturer for assistance. The vehicle was not repaired. The manufacturer was contacted; however, no assistance was provided. The contact was referred to the NHTSA Hotline for assistance. The failure mileage was 75,002. The VIN was not available.

The car seems to lose power sometimes when you are going down the road. My engine light came on but it brings up a fuel cap code, and a emission control sensor. The extended warranty covered the emissions control purge valve. This started around 70,000 miles.

The contact owns a 2020 Ford Fusion. The contact stated that while attempting to drive forward after reversing the vehicle, the vehicle failed to move. The wrench symbol displayed stating there was a system malfunction however, the contact was unsure of the system failure. The contact stated that the diagnostic App linked to the vehicle stated that there was power train malfunction causing reduced power. The contact stated that someone mechanically inclined inspected the vehicle and informed her that the cable shifter bushing had detached causing the gear shifter to move from drive to park. The contact had not taken the vehicle to the dealer. The vehicle had not been repaired. The manufacturer was made aware of the failure and referred the contact to the NHTSA Hotline. The approximate failure mileage was 80,000.

Fusion is surging while shifting or lack of. Some of them being more violent than others, sometimes pulling the steering wheel to the left or right. When coming to a stop in city driving when the fusion doesn’t shift the fusion stalls. The initial shift is also very rough into any gear (drive, reverse, and/or back to neutral.

The contact owns a 2020 Ford Fusion. The contact stated that the gear shifter failed to shift into the intended gear and the vehicle would not drive forward. Upon inspection, it was discovered that transmission fluid had leaked from the vehicle. The vehicle was towed to the local dealer who diagnosed that the transmission had failed and needed to be replaced. The vehicle was not yet repaired. The manufacturer was notified of the failure. The failure mileage was 66,000.