2015 RAM 3500 — Problems, Recalls & Safety Data

There was a recall forced by the NTSB for a condition where the track bar adjustment nut would come loose and the truck would lose steering. The recall on the track bar was rectified by the dealer by welding the nut on the track bar. Now that the nut has been welded a proper alignment can not be preformed. There is no longer adjustment available due to the welded nut. The only way to properly fix this is to replace the track bar. I have had many communications with ram (stellantis) and they refuse to remedy this as they tell me they have complied with the NTSB’s resolution.

There was a recall forced by the NTSB for a condition where the track bar adjustment nut would come loose and the truck would lose steering. The recall on the track bar was rectified by the dealer by welding the nut on the track bar. Now that the nut has been welded a proper alignment can not be preformed. There is no longer adjustment available due to the welded nut. The only way to properly fix this is to replace the track bar. I have had many communications with ram (stellantis) and they refuse to remedy this as they tell me they have complied with the NTSB’s resolution.

At about 3,000 miles I noticed a periodical head light flicker and intermittent radio issues. Shortly after that the truck has presented with periodical brake issues. My front brakes parodically drag and get hot. Typically on one front side or the other. However on [XXX] my wife and I took the truck out for a drive and both front brakes began dragging and heated up. I had to be towed 40+ miles back home. Two of my neighbors can verify I've had issues with the brakes on multiple occasions for several years now. I've had to limp the truck home on several occasions while in town and in Feb. 2025 it put my wife and I in what a consider a dangerous situation by stranding us on the side of the highway. I don't remember any warning lamps coming on but I did a scan after I got the truck back home. B170-15, B210A-16, B222C, B2861-15, P2509 & P2560 were present. I used my scanner to delete the codes and reset the EMC but am a bit hesitant to take the truck out on the road. Note: The truck has experienced a weird and harsh vibration on back of truck as well. I stop, shut engine off - do a walk around but haven't been able to pinpoint anything. Crank engine back up and problem has seemingly resolved itself. I think it's possibly a brake issue as well. At present this truck has less than 11,000 miles on it. Yes, LOL, less than 11,000 miles. Calipers and pads are in excellent functioning order. Fluid is easily pushed back into reservoir with no restrictions and no apparent degradation of flexible lines. I considered the brake fluid might have moisture built up in the system so I had a complete fluid replacement done but problem has persisted.I did read there's a recall on the the HCU/ABS unit and my truck seems to be in that category but haven't received anything from FCA. [XXX] Your attention and assistance would be greatly appreciated. Thank You. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

the instrument panel dash cluster went black and now I have no information like tire pressure, mph, engine oil temp, coolant temp, cruise control,parking sensor alert, ect. I have tried everything to reboot or see if there is loose connections and have come up with nothing. this could be a hazard.

The contact owns a 2015 Ram 3500. The contact stated while driving 60 MPH, the steering started shuddering and the vehicle made an abnormal popping sound. The contact then noticed that the front driver's side wheel was wobbling. The contact pulled over to the side of the road and inspected the wheel. The contact noticed that two of the wheel studs of the front driver's side wheel had fractured. The contact stated that the vehicle was previously taken to the dealer to be repaired under NHTSA Campaign Number: 21V398000 (Wheels); however, the dealer informed the contact that the wheel studs did not need to be replaced. The dealer was notified of the failure and informed the contact that the VIN was no longer included in the recall because the recall had been marked completed. The vehicle was not repaired and remained on the side of the road. The manufacturer was not notified of the failure. The failure mileage was approximately 166,000.