2021 JEEP GLADIATOR Engine Problems

The contact owns a 2021 Jeep Gladiator. The contact stated that while driving approximately 35 MPH, the vehicle started losing motive power. The contact stated that there were several unknown warnings illuminated, and the instrument cluster had started flashing on and off. The contact stated that the vehicle slowed down while depressing the accelerator pedal and continued to lose motive power. The contact stated that a warning flashed on the instrument cluster to "Pull Over" and that "Vehicle Was Going to Shutdown". The contact stated that the steering wheel became difficult to turn to the left or the right and that the brake pedal was difficult to depress, requiring the activation of the parking brake to stop the vehicle. The contact had the vehicle towed back to the residence. The contact stated that her husband determined that the 12-Volt battery needed to be replaced. The contact stated that a new...

I am writing regarding my 2021 Jeep Gladiator Mojave, which recently suffered engine damage due to a faulty head gasket. I understand the vehicle is approximately 5,000 miles over the 60,000-mile warranty; however, I believe this issue should not be my financial responsibility given the circumstances. At around 60,000 miles, I brought my Jeep in for a full service and inspection to ensure it was in top condition. I was informed at that time that everything looked fine and that there were no issues to address. Since then, I’ve continued to maintain the vehicle properly and drive it with care. The sudden head gasket failure, which ultimately led to engine damage, came as a complete surprise. This situation has been extremely difficult — not only because of the unexpected cost, but also because this Jeep was meant to be my long-term vehicle. My family and I have been loyal Mopar...

The contact owns a 2021 Jeep Gladiator. The contact stated that while driving at 60 MPH, there was an alarming amount of white smoke emanating from the engine compartment and permeating the interior of the vehicle, prompting the contact to pull over to the shoulder of the roadway and evacuate the vehicle. Moments later, the entire front of the vehicle was completely engulfed in flames. Local Emergency Services arrived on the scene and were able to extinguish the fire. During the failure several unknown warning lights were illuminated. The vehicle was towed to the residence and deemed a total loss by the Insurance provider. A fire report was filed and preliminary findings on the potential cause of the fire were provided but the contact was unaware of the cause. A Police report was filed, and injuries were reported. The contact's father suffered minor burns to both hands but had not...

Hi - So my 2021 Jeep gladiator has 2 batteries. The battery that controls the auto start-stop system failed (while driving). I was at a light on a busy road and the auto stop/start kicked in at a light but because of the failed second battery with no warning, my Jeep died would not start backup and I was unable to even get it into neutral. So I was forced to sit in heavy traffic until the wrecker came. My complaint it why no warning and why did it go into auto stop mode when the battery was in a failed situation.

Failed Right intake camshaft and roller rocker arm. Failure causes misfires and limp mode to be activated when trying to pass and accelerate and in my case was while going up a hill and unable to complete a safe pass of another truck. Known issue by Jeep and Stellantis as they have redesigned a kit for this specific part and upgraded software to increase pressure to the oiling system, but they have failed to replace parts and are 12000 orders behind on parts at ths current moment truck has been undriveable for greater than 45 days. Flashing check engine light and warning lights in place

Multiple cylinders miss fire, Camshaft 1 position slow responding. cylinder2, 4, and 6 repeatedly misfire. Passenger side engine is making excessive noise. This is the information given to me by Van Horn jeep mechanic. also confirmed by advanced auto. Advanced auto stated this is the 3rd jeep they have had in their shop recently to replace a faulty Camshaft. My Jeep only has 66024 hwy miles. Vin [XXX] (2021Jeep Gladiator) INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

My vehicle has about 17,000 miles. Both key fobs are failing to connect with the vehicle. The batteries have been checked by the dealership to determine the fobs are in working order. Without having the fob work, I am unable to unlock my doors or start the engine. Thankfully, learnng my fobs were not connecting occured while in my garage at my home. However, if this occured while away from home, or at night, I would have been stranded with no access to drive the vehicle. My Gladiator will have to be towed to the dealership now to get this resolved.

The contact owns a 2021 Jeep Gladiator. The contact stated that while operating the vehicle a valve knocking noise was present coming from the engine compartment, the check engine light had illuminated and the vehicle would not properly accelerate. The contact received codes that indicated an engine misfired in cylinder three and cylinder five. The vehicle was taken to the local dealer. The cause of the failure was not yet determined. The manufacturer was notified of the failures. The failure mileage was 98,000.

The contact owns a 2021 Jeep Gladiator. The contact received notification of NHTSA Campaign Number: 22V767000 (Fuel System, Gasoline, Engine) however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The dealer was made aware of the issue and confirmed that parts were not yet available. The manufacturer was made aware of the issue and confirmed that parts were not yet available. The contact had not experienced a failure. Parts distribution disconnect.

The contact owns a 2021 Jeep Gladiator. The contact received notification of NHTSA Campaign Number: 22V767000 (Fuel System, Gasoline, Engine) however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The dealer was made aware of the issue and confirmed that parts were not yet available. The manufacturer was made aware of the issue and confirmed that parts were not yet available. The contact had not experienced a failure. Parts distribution disconnect.

The contact owns a 2021 Jeep Gladiator. The contact received notification of NHTSA Campaign Number: 22V767000 (Fuel System, Gasoline, Engine) however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. While the contact was driving at approximately 35 MPH, the vehicle made an abnormal sound in the engine compartment and then stalled. The vehicle was towed to a dealer and diagnosed with fuel pump failure. The failure mileage was approximately 46,000. Parts distribution disconnect.

Truck has death wobble. Truck steering motor gets stuck at times. Truck has electrical problems and computer problems. The steering is bad and the suspension is loose. I feel unsafe driving this truck.

The contact owns a 2021 Jeep Gladiator. The contact received notification of NHTSA Campaign Number: 22V767000 (Fuel System, Gasoline, Engine) however, the part to do the recall repair was not yet available. An undisclosed dealer was contacted and confirmed that parts were not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The contact stated that on two separate occasions while driving approximately 60-75 MPH, the vehicle inadvertently decelerated while the accelerator pedal was depressed. No warning light was illuminated. The vehicle was taken to the dealer where it was diagnosed that the high-pressure fuel pump had failed and needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure and the contact was offered to replace the failure part with a temporary repair however, the contact declined due to the concern for his safety....

The contact owns a 2021 Jeep Gladiator. The contact received notification of NHTSA Campaign Number: 22V767000 (Fuel System, Gasoline, Engine) however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The dealer was made aware of the issue. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.

IT GOT 7 PROBLEM ISSUES AND ALMOST LOST CONTROL DUE TO ELECTRONIC THROTTLE CONTROL FAILED WHILE DROVE ON FREEWAY AND TOW TEARDROP (1400 LBS) . MALFUNCTION INDICATOR LIGHT, TRACTION ON (COULD NOT TURN OFF), ELECTRONIC STABILITY CONTROL ACTIVE POPPED UP ( COULD NOT TURN OFF), SERVICE FORWARD COLLISION WARNING LIGHT, CRUISE CONTROL FAULT WARNING LIGHT, SERVICE STOP/START SYSTEM WARNING LIGHT, SERVICE ADAPTIVE CRUISE CONTROL WARNIING LIGHT (ALL OF THEM POPPED UP THAT COULD NOT TURN OFF). I WENT TO JIM CLICK JEEP DEALERSHIP AND THEY NEVER SEEN THEM BEFORE. I AM VERY DISAPPOINTED AND I FEEL THAT MY TRUCK IS "LEMON" I TOLD THEM TO FIX ASAP BUT THEY CAN NOT FIX AND HAVE TO WAIT TILL AUGUST 9 (APPOINTMENT) TO CHECK WHATS WRONG.

There is one safety recall on the truck that jeep won't fix 22V-767 its been almost a year and there still isn't any fix. There is also an EMISSIONS RECALL Y81 that they also won't fix that is preventing me from smog and registering the vehicle in California.

The contact owns a 2021 Jeep Gladiator. The contact received notification of NHTSA Campaign Number: 22V767000 (Fuel System, Gasoline, Engine) however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. Parts distribution disconnect.

The contact owns a 2021 Jeep Gladiator. The contact received notification of NHTSA Campaign Number: 22V767000 (Fuel System, Gasoline, Engine) however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue and confirmed that parts were not available. The contact had not experienced a failure. VIN tool confirms parts not available.

The contact owns a 2021 Jeep Gladiator. The contact received notification of NHTSA Campaign Number: 22V767000 (Fuel System, Gasoline, Engine) however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.

The contact owns a 2021 Jeep Gladiator. The contact stated while driving at various speeds, she noticed an abnormal clicking sound coming from the rear of the vehicle and the vehicle failed to accelerate as needed. The contact also stated that she had received several messages from Uconnect indicating a Power System failure. The vehicle was taken to the dealer where it was diagnosed that the failure was associated with the parking brake due to unknown components being detached and hanging underneath the vehicle. The dealer repaired the parking brake; however, the failure persisted. The vehicle was not repaired. Additionally, the contact received notification of NHTSA Campaign Number: 22V767000 (Fuel System, Gasoline, Engine). The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was notified of the failure. The failure mileage was approximately 26,000. VIN tool...

Under heavy breaking the rear wheels of my vehicle lifted off of the pavement. This loss of traction and shift in weight resulted in a head on collision with a vehicle in the opposite lane of traffic. After the accident I discover that the suspension for my vehicle was incorrect to the level that FCA released a TSB regarding the issue. The suspension that was equipped with the vehicle was designed for the gasoline motor and the weight associated with that motor. My vehicle has the diesel motor (approximately 600lbs heavier) along with factory equipped steel bumpers adding additional weight. This factory design failure created a vehicle that could not perform as designed and as I found out via an automotive accident, a vehicle that under heavy breaking can lift its rear wheels off of the ground.

The vehicle suddenly accelerates. The rpm’s shoot up real high, the Jeep accelerates and the brakes do NOT work. This has occurred while driving at 55-60 mph and twice driving in city traffic going approx. 30-35. The acceleration increases and is stuck. I press the brakes and they do not work until whatever is sticking releases.

The contact owns a 2021 Jeep Gladiator. The contact received notification of NHTSA Campaign Number: 22V767000 (Fuel System, Gasoline, Engine) however, the part to do the recall repair was unavailable. The contact stated while driving approximately 60 MPH, the vehicle started losing motive power, and then after a minute the vehicle functioned normally. The contact stated that there was no warning light illuminated. The contact stated that the failure was intermittent. The dealer was contacted to have the vehicle diagnosed and repaired; however, the dealer advised that the failure could be related to NHTSA Campaign Number: 22V767000 (Fuel System, Gasoline, Engine) however, the part was not yet available. The vehicle was not repaired. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The failure mileage was approximately 21,000. VIN tool confirms parts not...

On 3 different occasions the acceleration got stuck and increased speed. I pressed the brake over and over and the Jeep would NOT reduce speed or slow down for what ranged between 30 - 45 seconds. Had there been a vehicle directly in front of me I would have slammed into the vehicle. If I had been trying to stop at an intersection I would not have been able to stop. I had my child in the car two out of the three times this has occurred. The dealership states that they have not had any complaints of this occurring and could not replicate it during the few minutes they drove it and do not seem to be concerned that this issue could seriously injure or kill me, my child, or others. This is a SERIOUS issue that should be addressed immediately.

2021 JEEP GLADIATOR. CONSUMER WRITES IN REGARD TO STOP/START SYSTEM NOT FUNCTIONING. THE CONSUMER STATED THE STOP/START FEATURE READS AS NOT READY. THE DEALER WAS UNABLE TO DETERMINE THE CAUSE OF THE FAILURE.

I was driving the vehicle, while towing a 5000lb trailer (vehicle tow rating is 6000lb), up a 4-5% grade at 4000'-6000' elevation, with ambient temperature around 80 degrees, and the vehicle unexpectedly derated / limited speed to approx 45 mph with no warning indicators on the vehicle. I had a number of cars and semi trucks behind me, and so I unexpectedly needed to find a safe place to pull over, which was limited due to the road conditions. I travel in areas frequented by semi trucks with limited shoulders. If I had not found a pull-out, this could have been dangerous. This appears to be an issue countered by a number of Jeep Gladiator Diesel owners, relating to either engine oil temperature too high, or EGT temp too high when towing uphill.

Engine oil temperature reached 265 degrees while towing within capacity - engine derated power and I could not drive above 35mph on a road with a speed limit if 75mph. It was dangerous!

While towing a trailer the vehicle suddenly reduces power to less than half and multiple check engine lights appear. This seems to happen only when outside temperatures are above 80f. I went from going 65mph to 45mph within 1/4 mile which caused sudden traffic issues behind me. I have had the vehicle to the dealer multiple times and they do not find anything even though there are multiple engine lights. I have had it happen a over 8 times in 1 year. I also have a co-worker that has had the same issue.

3.0 EcoDiesel in the Jeep Gladiator has cooling issues. Thousands of users affected and discussing on forums and on Facebook groups but the manufacturer is unwilling to fix. Core of the issue is that the engine was altered in the Gladiator and Wrangler over previous installations in the Ram and Grand Cherokee by removing oil coolers and a larger oil pan, which has resulted in high oil temps. At 265 degrees (which is accomplished easily during the summer with a trailer UNDER the tow rating), the engine starts derating and limp mode. The aftermarket community has tested everything ... removing hoods, fenders different cooling solutions, etc and nothing is working at the moment other than aftermarket solutions to cool the oil (which are negligible at best at the moment due to the space constraints imposed by the engine being quite large in the engine bay not not substantial room for...

After stopping for fuel in Quartzite, Arizona I began to merge onto HWY 10. As I accelerated the vehicle limited my speed to 45 MPH. This is on a 70 MPH section with heavy truck traffic. I was able to pull onto the shoulder and limp to the next exit without incident. I then drove around backroads for 10 minutes, starting and stopping the vehicle and accelerating to 55 MPH. After this period of time the vehicle operated normally. This happened with no warning at all, temperatures were all within normal ranges. Since the incident I have found that this "derating" is common to the diesel engine in hot ambient temperatures or while going up hill. My safety was definitely at risk, in a different scenario it could have been much worse. I have spoked with several factory service centers and Jeep directly, they say they have never heard of...

When operating the vehicle under heavier loads (5%+ grades, towing even light trailers, higher highway speeds) vehicle loses power limiting speed to 15-50mph depending on how hot the water or oil temperature is. I have had this issue in ambient temperatures as low as 31°F while towing 4000lb up a steep incline, but will absolutely overheat if ambient temp is over 100°F. Vehicle must be left running during a fuel stop or heat soak caused by the vehicle is not running will prevent me from merging back on the highway at a safe speed....max speed is 50mph until the engine oil cools off. Air conditioner use as expected makes the problem worse. There are many threads going on the Jeep internet forums with many diesel equipped Jeep Wranglers and Gladiators having the same issues, so I know these aren't isolated incidents from my vehicle alone. If you were to search...

Overheating during normal driving.

The vehicle randomly stalled out / died while idling, with the clutch pedal fully engaged. This poses a serious safety hazard as the vehicle may unexpected stall out at a traffic light or while driving resulting in a serious accident. The most likely risk is a stalled out vehicle in heavy traffic resulting in a rear end collision. The vehicle stall out and failure to maintain idle malfunction was reported to the local dealership and an FCA Technical Advisor (TA). The vehicle’s stall out was witnessed and documented by an independent mechanic. However, the dealership and FCA TA continue to state that the vehicle is “operating as designed” and that “this is normal characteristic of the vehicle”. These claims indicate that the Jeep Gladiator Engineering Design Team intentionally designed the vehicle to stall out with the driver completely pressing in the clutch pedal. The vehicle is available for inspection upon...

The vehicle’s throttle spikes / surges when the driver completely lifts off the accelerator and presses in the clutch. The issue indicates the throttle sticks after the driver lifts off the accelerator. The issue happens in multiple gears at various RPMs. The issue happens with or without the climate controls off. The issue regularly occurs in 4th gear at 44 mph at ~1900 RPMs. On 1/26/2021 while on a ride along, the customer and Service Tech at Texan DCJR were able to recreate the issue multiple times. On 1/29/2021, the Service Director at Texan DCJR stated to the customer that he and 3 members of his team were able to recreate the issue multiple times. However, the Service Director falsified and backdated the service records to 1/28/2021 claiming that they “couldn’t duplicate concern” and that the “vehicle is driving normal.” After two inspections, the FCA TA claimed that he “couldn’t...

The vehicle’s throttle bounces and surges off idle, in direct opposition to the driver’s inputs to the controls. After the driver lifts off the accelerator and engages the clutch, the RPMs drop slowly to idle, then the throttle regularly bounces and surges without user input to the controls by ~500 to ~1,500 RPMs. The issue occurs while driving in every gear and or in neutral. The issue occurs frequently but not every time. The issue occurs with or without the driver’s foot on the brake. The failure to maintain idle malfunction was reproduced and confirmed by multiple service personnel at the local dealership. However, the Service Director falsified and backdated the service records to claim that they “couldn’t duplicate concern” and that the “vehicle is driving normal.” The throttle spike off idle was recreated by 4 independent mechanic shops and documented as a safety concern. An FCA TA claimed that...

The vehicle’s throttle surges sporadically when shifting gears without driver input to the accelerator / controls. The issue impacts the driver’s ability to operate the vehicle safely in heavy traffic or dynamic situations. The throttle surges while shifting introduce delays to driver reaction times, and they create a safety hazard in heavy traffic where fractions of a second can make the difference in a major accident. The throttle surge while shifting malfunction was reproduced and confirmed by multiple service personnel at the local dealership. However, the Service Director falsified and backdated the service records to claim that they “couldn’t duplicate concern” and that the “vehicle is driving normal.” The throttle surge while shifting was recreated by 4 independent mechanic shops and documented as a safety concern. An FCA Technical Advisor (TA) claimed that the vehicle was “operating as designed“ both when he could not recreate the issue and when he...

The vehicle’s Auto Start / Stop System activates and shuts off the vehicle while the instrument cluster reads “STOP/START NOT READY”, in direct conflict with owner’s manual. Per the owner’s manual, the first condition for an Auto Stop with a manual transmission is that the instrument cluster must read “READY”. Other Jeep vehicles, clearly show “READY” on the instrument cluster before shutting off. However, the Jeep Gladiator presents a false / incorrect “NOT READY” notification to the driver on the instrument cluster before shutting off. This anomaly with the Auto Stop / Start System distracts the driver and creates confusion impeding normal driving operations such as stopping at traffic lights / signs, pedestrian areas, and parking lots. This poses a serious safety hazard as the vehicle will unexpectedly shut off when the driver is not prepared and presented with an incorrect notification warning. In heavy traffic, this could lead to...

The vehicle auto stops when putting on the driver’s seat belt, in direct conflict with owner’s manual. The owner’s manual specifies that if the “Driver’s seat belt is not buckled” it will prevent an auto stop, but preventing the auto stop is the opposite of the act of buckling the seat belt initiating the auto stop. Furthermore, the instrument cluster does not present a “STOP/START READY” message which is the first necessary condition for an auto stop. This issue creates a serious safety hazard, as the vehicle presents factually incorrect information to the driver and the vehicle unexpectedly stops creating driver confusion and distraction. Additionally, this creates a serious safety hazard as the issue inhibits the driver from attempting to flee an emergency situation, wherein the driver hops into an idling vehicle, plugs in their seat belt, and the vehicle turns itself off. The malfunction was reproduced and confirmed by...

The vehicle auto stops when turning down or turning off the climate controls, in direct conflict with owner’s manual. This condition is not listed as one of the three conditions to activate an auto stop in the owner’s manual. This condition is also not listed as one of the conditions that will inhibit the vehicle from an auto stop in the owner’s manual. Furthermore, the instrument cluster never presents a “STOP/START READY” message which is the first necessary condition for an auto stop. This issue creates a serious safety hazard, as the vehicle presents incorrect information to the driver and the vehicle unexpectedly stops in traffic which confuses and distracts the driver. The unexpected / wanted stop in heavy traffic could cause a rear-end collision leading to serious injury or death. The malfunction was reproduced and confirmed by multiple service personnel at 2 different dealerships, who expressed safety concerns. The...

The vehicle auto stops when the hood is closed and the driver remains in the seat with the seat belt buckled. The owner’s manual specifies that an open hood will prevent an auto stop, but preventing the auto stop is the opposite of closing the hood initiating the event. Furthermore, the instrument cluster never presents a “STOP/START READY” message which is the first necessary condition for an auto stop. This issue creates a serious safety hazard, as the vehicle presents incorrect information to the driver and the vehicle unexpectedly stops which confuses and distracts the driver. Additionally, after jump starting another vehicle, the vehicle’s battery may be sufficiently depleted. Upon closing the hood, the vehicle could auto stop, and with the numerous other malfunctions impacting the auto stop system the vehicle may not be able to restart possibly leaving the driver stranded. The unexpected / wanted auto stop could cause...

The vehicle auto stops when the driver’s seat is not occupied, in direct conflict with owner’s manual. The owner’s manual specifically states that if the “Driver’s seat is not occupied” that the “engine will not stop.” Note that this system safety check is separate and distinct from the “Driver’s seat belt is not buckled” check. Furthermore, the instrument cluster never presents a “STOP/START READY” message which is the first necessary condition for an auto stop. The vehicle fails to properly check for the empty driver’s seat safety condition before auto stop. This auto stop violates Jeep’s published safety check condition and poses a serious safety hazard. This issue poses additionally serious safety hazards as the vehicle will shut off with the driver outside the vehicle, leaving the driver with an incorrect understanding that the vehicle is properly locked out from an auto start condition. Therefore, if the driver is operating...

The failure of the vehicle’s safety condition check for an empty driver’s seat for an auto stop indicates that the “Occupant Restraint Controller (ORC)” and/or the “Advanced Front Air Bag system” are not receiving proper information. This creates a serious safety hazard as the front air bags may not deploy or may not “adjust the inflation rate of the Advanced Front Air Bags” as specified in the owner’s manual. For driver safety, these systems and their associated sensors should be fully examined and tested. The vehicle auto stops when the driver’s seat is not occupied, in direct conflict with owner’s manual. The owner’s manual specifically states that if the “Driver’s seat is not occupied” that the “engine will not stop.” Note that this system safety check is separate and distinct from the “Driver’s seat belt is not buckled” check. The vehicle fails to properly check for the empty driver’s seat...

The vehicle auto stops when the steering wheel is turned, in direct conflict with owner’s manual. The owner’s manual specifies that “Steering angle beyond threshold” will prevent an auto stop, but preventing the auto stop is the opposite of initiating the event. Furthermore, the instrument cluster never presents a “STOP/START READY” message which is the first necessary condition for an auto stop. This issue creates a serious safety hazard, as the vehicle presents incorrect information to the driver and the vehicle unexpectedly stops in traffic which confuses and distracts the driver. The unexpected / wanted stop in heavy traffic could cause a rear-end collision leading to serious injury or death. The malfunction was reproduced and confirmed by multiple service personnel, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle...

The vehicle auto stops when the defrost is turned off, in direct conflict with owner’s manual. The owner’s manual specifies that “HVAC is set to full defrost mode” will prevent an auto stop, but preventing the auto stop is the opposite of initiating the event. Additionally, this issue occurs when the HVAC is operating at less than full defrost mode. Furthermore, the instrument cluster never presents a “STOP/START READY” message which is the first necessary condition for an auto stop. This issue creates a serious safety hazard, as the vehicle presents incorrect information to the driver and the vehicle unexpectedly stops in traffic which confuses and distracts the driver. The unexpected / wanted stop in heavy traffic could cause a rear-end collision leading to serious injury or death. The malfunction was reproduced and confirmed by multiple service personnel, who expressed safety concerns. The malfunction was also recreated by 4 independent...

The vehicle auto starts when opening the driver’s door. This is not listed under “Conditions that will cause the engine to start automatically while in STOP/START AUTO STOP ACTIVE mode” in the owner’s manual. Other Jeep models do not auto start upon opening the driver’s door. This auto start issue poses a serious safety hazard as the vehicle will unexpectedly start and begin to roll when the driver’s door is open and the driver is not properly secure in the driver seat. The unexpected / wanted start could cause a collision with another vehicle or pedestrian leading to serious injury or death. The malfunction was reproduced and confirmed by multiple service personnel at 2 Jeep dealerships, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as a safety concern. However, an FCA Technical Advisor (TA) claimed that the vehicle is “operating as designed“....

The vehicle auto starts when the brake pedal is pressed. The owner’s manual does not list this as one of the “Conditions that will cause the engine to start automatically”. The vehicle is operating in direct conflict with owner’s manual. This auto start issue poses a serious safety hazard as the vehicle will unexpectedly start and begin to roll when the driver is not ready. Additionally, if someone is operating on or under the vehicle, it will result in a serious injury or the loss of a finger when the vehicle auto starts in violation of the driver’s intent. The unexpected / wanted start could cause a collision with another vehicle or pedestrian leading to serious injury or death. The malfunction was reproduced and confirmed by multiple service personnel at 2 Jeep dealerships, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as...

The vehicle auto starts when the defrost is turned on below the max or full setting. The owner’s manual specifies that “the engine will start automatically when” the “HVAC is set to full defrost mode”. The vehicle is operating in direct conflict with owner’s manual. This auto start issue poses a serious safety hazard as the vehicle will unexpectedly start and may begin to roll when the driver is not ready. Additionally, if someone is operating on or under the vehicle, it will result in a serious injury or the loss of a finger when the vehicle auto starts in violation of the driver’s intent. The unexpected / wanted start could cause a collision with another vehicle or pedestrian leading to serious injury or death. The malfunction was reproduced and confirmed by multiple service personnel, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and...

The vehicle auto starts when the fan is turned on without the AC. The owner’s manual does not list this as one of the “Conditions that will cause the engine to start automatically”. The vehicle is operating in direct conflict with owner’s manual. This auto start issue poses a serious safety hazard as the vehicle will unexpectedly start and may begin to roll when the driver is not ready. Additionally, if someone is operating on or under the vehicle, it will result in a serious injury or the loss of a finger when the vehicle auto starts in violation of the driver’s intent. The unexpected / wanted start could cause a collision with another vehicle or pedestrian leading to serious injury or death. The malfunction was reproduced and confirmed by multiple service personnel, who expressed safety concerns. The malfunction was also recreated by 4 independent mechanic shops and documented as...

The vehicle auto starts when the AC is turned on with the Auto HAVC set to off. The owner’s manual states that “the engine will start automatically when” the “Actual cabin temperature is significantly different than temperature set on Auto HVAC.” The vehicle is operating in direct conflict with owner’s manual. This auto start issue poses a serious safety hazard as the vehicle will unexpectedly start and may begin to roll when the driver is not ready. Additionally, if someone is operating on or under the vehicle, it will result in a serious injury or the loss of a finger when the vehicle auto starts in violation of the driver’s intent. The unexpected / wanted start could cause a collision with another vehicle or pedestrian leading to serious injury or death. The malfunction was reproduced and confirmed by multiple service personnel, who expressed safety concerns. The malfunction was also recreated...

The vehicle fails to maintain idle. During normal driving conditions the idle spikes significantly and noticeable from 200 – 2,000 RPMs. The throttle surges unpredictably without driver input to the controls. The failure of the vehicle to maintain idle creates a serious safety hazard as it distracts the driver’s attention and substantially impairs the vehicle’s use during routine driving tasks. The failure to maintain idle malfunction was reproduced and confirmed by multiple service personnel at the local dealership. However, the Service Director falsified and backdated the service records to claim that they “couldn’t duplicate concern” and that the “vehicle is driving normal.” An FCA TA stated that, “There are certain scenarios where the engine's idle speed may increase normally without accelerator input, this would include A/C operation or alternator charging requirements, however the difference in rpm is very slight and most people do not notice it and it will not...