2019 MAZDA CX-9 — Problems, Recalls & Safety Data

- Coolant leak at cylinder head and turbo at only 63,000 miles. - Safety issue because no warning lamps or messages appeared and potential for car to overheat without coolant circulating in the system. Car could breakdown at worst time and location. Leaking coolant onto exhaust created potential for fire. - Problem has not been confirmed by dealer yet. Appointment is upcoming. - Symptoms of the problem were leaking coolant on ground, low coolant level, heater not working properly. - First appeared 1/29/2026.

Mazda has a current service alert ("SA", SA-001/23) for issues with their Gen 6 Infotainment Center Display, which covers issues (e.g. ghost touch, surface peeling, spider cracks, and white dots) and defects the occur on the primary display of the car. This display provides the driver with essential car operational information. This service alert applies to may of their vehicles in the 2014-2021 range, dependent on model. This VIN provided [XXX] ) is associated with a 2019 CX-9 that within the last month started displaying spider cracks at 2 of the 4 corners of the display. Even though this is a known (manufacturer) issue with other cars that utilize this display, the local Mazda dealership will not cover the replacement for this vehicle as the VIN range has not been included in this SA. The SA does not include CX-9s, but does include Mazda3 (Japan built) with applicable model years 2017-2018 (produced from June 27, 2016 to October 31, 2018). --> This 2019 CX-9 vehicle is Japan built, with a manufacture date of "10/18" (October 2018). Many other people are having this same issue [XXX] ). Please encourage Mazda to expand their Service Alert range for this repair, which should be free (product cost and labor should be both provided at no cost to the consumer) to replace since it's a material issue with the product, not an operator error.... as documented in their SA-001/23. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

The contact owns a 2019 Mazda CX-9. The contact stated that a State Inspection was performed on the windshield for cracks. The contact stated that while driving in the rain, the front windshield wipers turned on independently with the switch in the off position. The contact was unable to turn off the windshield wipers. The contact pulled over to the side of the road and turned off the vehicle. When the vehicle was restarted, the front windshield wipers had turned off. The contact stated that the failure persisted and worsened. The contact stated that occasionally the windshield wipers failed to turn off. The vehicle was taken to the dealer; however, no cause for the failure was found. The vehicle was not repaired. The contact purchased and replaced a sensor. Upon investigation, the contact became aware that the on and off switch for the front windshield wipers related to the sensor located on the front windshield. The contact stated that the sensor controlled the on and off switch and failed to function as intended. The contact stated that the OEM windshield provided protection against the sensor malfunctioning; however, if the front windshield was replaced with a non-OEM windshield, the windshield wipers would fail to operate as designed. The manufacturer was not made aware of the failure. The failure mileage was 56,199.

The contact owns a 2019 Mazda CX-9. The contact stated that a State Inspection was performed on the windshield for cracks. The contact stated that while driving in the rain, the front windshield wipers turned on independently with the switch in the off position. The contact was unable to turn off the windshield wipers. The contact pulled over to the side of the road and turned off the vehicle. When the vehicle was restarted, the front windshield wipers had turned off. The contact stated that the failure persisted and worsened. The contact stated that occasionally the windshield wipers failed to turn off. The vehicle was taken to the dealer; however, no cause for the failure was found. The vehicle was not repaired. The contact purchased and replaced a sensor. Upon investigation, the contact became aware that the on and off switch for the front windshield wipers related to the sensor located on the front windshield. The contact stated that the sensor controlled the on and off switch and failed to function as intended. The contact stated that the OEM windshield provided protection against the sensor malfunctioning; however, if the front windshield was replaced with a non-OEM windshield, the windshield wipers would fail to operate as designed. The manufacturer was not made aware of the failure. The failure mileage was 56,199.

1. What component or system failed or malfunctioned, and is it available for inspection upon request? ANSWER: Engine failure due to overheating. 2. safety & indicators: ANSWER: During evening rush hour traffic on a 3 lane highway my car went into a form of engine power saving mode while i had children in the vehicle; this was almost catastrophic form my family and the other vehicles around me. there was NO warning. there were no previous issues with my vehicle, this was unexpected. 3. technician review: this is a known issue with no warning: The technician inspected your vehicle and found a concerning issue with the engine overheating. They scanned the vehicle and found a trouble code P111A, indicating the engine coolant reached a temperature of 251.6 degrees Fahrenheit, forcing the engine into limp mode. Based on their experience, the technician believes the engine likely reached much higher temperatures, potentially causing internal damage to the engine block. After a thorough inspection, they found no external coolant leaks, but upon using a digital borescope, they discovered evidence of coolant entering and being burned off in Cylinder 3. Given the severity of the issue, the technician recommends replacing the entire engine to ensure the long-term reliability and extended life of your vehicle. Services completed: - Scanned vehicle and found trouble code P111A - Inspected engine and found no external coolant leaks - Used digital borescope to inspect cylinders and found coolant entering Cylinder 3 Recommendations: - Replace the entire engine