2016 MINI COOPER Electrical System Problems

The rear brake lights and rear signal indicator lights keep going in and out arbitrarily. It's dangerous because it will work fine and then just randomly stop working and then work again. People can't tell if I'm stopping or turning when this randomly occurs. This is currently not a recall on my Mini, however, I saw that it is a recall on other Minis and it seems mine is having the same issue so it's possible they all have similar or the same faulty wiring/electrical for the brake lights and signal indicator lights.

While driving straight on an Interstate highway at approximately 65 mph, the right front and left rear brakes momentarily locked up after the windshield wipers were turned on due to light rain starting to fall. This happened multiple times, only when the wipers were turned on. There were no warning lights illuminated in the instrument cluster or dash displays. This nearly caused a loss of vehicle control on several occasions and nearly caused an accident as well. The car has been routinely serviced to factory schedules including brake fluid time based changes. There appeared to be some occasional delay in the release of the brakes when starting from a stop. The brakes were serviced after this incident and the service center recommended completing a few panic stops to operate the ABS system. They could not explain how the wiper system can cause one circuit of the braking system to operate...

Rear passenger tail light casing/bucket had burnt connections. Replaced casing/bucket and bulb. Worked for short time, tail light failed a second time. Casing/bucket & bulb replaced, again worked for short time and then went out. Took vehicle to another mechanic after passenger side headlight failed. New mechanic checked casings/bucket - connections looked okay, however both wiring harnesses were severely burnt. Headlight harness was all bare wires. Mechanic unable to determine cause of the severe heat that would lead to both the headlight & taillight wiring harnesses becoming burnt so severely. Mechanic was concerned of the potential for this issue to cause vehicle fire. Suggested to follow up with dealership to have lights & wiring harnesses on Driver side checked After research online regarding this year/make/model - I have found numerous other reports of other owners experiencing the same issues with burned wiring harnesses causing both front and rear light failure...

* Component/ system that has malfunctioned and failed - The Driver side tail light circuit board and pig tail malfunctioned. The connector has corroded and the plastic plug housing looks melted on the earth / brown wire. This in return damages the the ground connection for the tail light rendering the turn signal the reverse light and the brake light inoperable on the effected side. YES, MY VEHICLE IS AVAILABLE FOR INSPECTION AT ANY TIME. *A driver behind an affected vehicle could be confused which could increase the risk of a crash. *The vehicle has been inspected by a licensed MINI Dealership. They failed to report two of the three nonworking rear lights that have failed due to the connector becoming corroded. The corroded plastic plug housing becomes melted on the earth / brown wire. This in return damages the the ground connection for the tail light rendering the turn...

There is a design issue resulting in failure of the connector for the rear tail light assembly. The connector corrodes and the plastic plug housing melts. This damages the ground connection for the tail light rendering the turn signal and brake light inoperable on the effected side. This has happened on the right rear of our Mini Cooper JCW hardtop. Searching on the web shows this to be a common problem for the F55, F56 & F57 MINIs. As this failure makes the car brake light system non-compliant with FMVSS lighting requirements, there should be a recall to address this issue.

Rear tail lights have a bulb socket and a 6-pin connector that have a tendency to burn at the brown ground wire where the connector and bulb socket meet. Requiring replacement of both parts and disabling the rear tail light (brake, turn, and reverse lights). It requires rewiring the 6-pin connector and replacing the bulb socket. About $60 in parts. When this occurs it an alert comes on the dash of a malfunction to all three rear lighting functions. One or all three of the lights can be affected. However, due to the complexity of the parts and labor required, it can be burdensome for people to diagnose and then afford to repair, if they don’t know how to repair themselves. Web searches helped me diagnose the issue and find the burnt connections on our vehicle, with folks commenting of a known issue on MINIs and BMWs for this type...

REAR LIGHT CONNECTOR OVER HEATING, MELTING AND SHORTING.