1987 FORD F250 — Problems, Recalls & Safety Data

WHILE DRIVING 55 MPH THE REAR DRIVER SIDE TIRE TREAD SEPARATED WITHOUT WARNING. PLEASE PROVIDE ADDITIONAL INFORMATION. *JB

BRIDGETONE, LT235/85R16, DOT: UNKNOWN. WHILE DRIVING 65 MPH, THE LEFT REAR TIRE TREAD SEPARATED. AS RESULT THE BUMPER, TAIL PIPE AND FENDER WAS DAMAGED. *AK *JB

WITH NO WARNING, RT FRONT TIRE BLEW APART. LOUD, LOUD BANG AND TRUCK JERKED ONTO THE SHOULDER, UP OVER A 2 FOOT HIGH BERM, AND TOOK NEARLY 300 YARDS TO STOP. NOTHING SEEN IN THE ROAD THAT I MAY HAVE HIT, TIRES HAD JUST BEEN SERVICED 1 WEEK PRIOR. (WE ARE EXTREMELY WE DID NOT ROLL OVER) TIRE HAS 4-5 SLITS GOING FROM TIRE BEAD TO TIRE TREAD, AND LOOKS LIKE THE TIRE BLEW RIGHT ACROSS THE TREAD. I DO HAVE THE TIRE, AND RETRIEVED SEVERAL FEET OF TREAD. HAVE NOT CONTACTED THE DEALER, AS I DON'T KNOW WHO MADE IT. OTHER DOT NUMBERS ON THE OTHER 3 TIRES ARE AS FOLLOWS (THE DOT # I GAVE EARLIER APPEARS TO BE CORRECT, HOWEVER, DAMAGE TO THE NUMBER OCCURRED) DOT VDOR 8AC 315, VDOR 8AC 076, VDOR 8AC 076. TIRES HAVE APPROXIMATELY 5000 MILES ON THEM AND WERE PURCHASED AT THE EDWARDS AFB EXCHANGE, EDWARDS AFB CA. 93524, ON 01/05/97. CAN YOU TELL ME IF THERE HAVE BEEN OTHER FAILURES SUCH AS THIS, AND ARE THERE ANY RECALLS ON THIS TIRE? THANK YOU, [XXX]. *AK (DOT NUMBER: VDOR8AC245 TIRESIZE: L235/85R16) PARTS OF THIS DOCUMENT HAVE BEEN REDACTED TO PROTECT PERSONALLY IDENTIFIABLE INFORMATION PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6).

THE CLUTCH FAILED TO DISENGAGE PROPERLY AND PLACED ME IN A HAZARDOUS DRIVING SITUATION. THIS CLUTCH IS HYDRAULICALLY OPERATED AND A DEALER REPAIR WAS TO REPLACE THE CLUTCH MASTER CYLINDER. THIS DID NOT CORRECT THE PROBLEM. I INVESTIGATED THE OPERATION OF THE CLUTCH AND FOUND THE CAB FIREWALL, WHERE THE CLUTCH MASTER CYLINDER IS BOLTED TO IT, DOES NOT HAVE ENOUGH STRENGTH TO SUPPORT THE CLUTCH OPERATIONAL STRESSES APPLIED TO IT. THIS FIREWALL HAD STARTED TO SEPARATE AND ALLOWED THE CLUTCH MASTER CYLINDER TO MOVE WHEN IT WAS ACTUATED, THEREBY THE CLUTCH WAS NOT ABLE TO DISENGAGE.*AK

I HAVE OWNED 2 F250 PICKUPS. ONE 1983 AND ONE 1987. THEY BOTH HAVE HAD 2EA FAILURES OF THE FUEL LINE TO CARBURATOR FLOAT BOWL FITTING. THE FLOAT BOWL PART NUMBER FROM FORD IS E5TZ 9510-MB. THE THREADED BORE OF THE FLOAT BOWL BECOMES BELL SHAPED OVER TIME. THIS CAUSES FUEL TO LEAK BETWEEN THE FUEL LINE AND FRONT FLOAT BOWL. THIS FUELS LEAKS ON THE HOT MANIFOLD. FORD KNOWS OF THE PROBLEM AND SIMPLY RAISED THE PRICE ON THE REPLACEMENT PART TO EARN MORE PROFIT. IT USED TO BE LESS THAN $50 AND CURRENTLY IS OVER $80. I WILL SEND TWO SAMPLES OF THE PART SO YOU MAY SEE FOR YOURSELF WHAT IS HAPPENING. THIS IS A MAJOR SAFETY ISSUE AND I HAVE NO DOUBT AFFECTS THOUSANDS OF FORD F250'S. *AK