2018 ACURA TLX — Problems, Recalls & Safety Data

I was rolling up to a stop light at approximately 20 mph when the frontal crash mitigation feature suddenly slammed the brakes on fully to a complete stop. I searched the web and found that there are other owners of this model that have had similar occurrences. I could easily have been rear-ended if someone had been following. I was lucky that didn’t happen. Since that day, I have been afraid to drive the car until I have disabled the feature.So every time I start my car I have to disable this mode. There is no known fix. No technical service bulletins etc. regarding this problem. Honda Acura needs to find a solution to this. I should not have to disable a safety feature that is actually making my car unsafe!

The vehicle experienced vibration symptoms and stalled on the road. The day before it stalled, there were rattling noises which prompted me to take the car to the dealership the next day. I had just received the letter about the recall so I knew it was likely related. The car was towed to the Acura dealership but the dealership denied recall coverage, stating the engine number did not match the recall list. During the discovery process, it was later discovered that the engine had been swapped by the dealership in 2018 — a fact that was not disclosed to me at the time of my purchase. The installed engine still falls within the recall defect interval of 2015-2020 but they are resistant to repair. Upon initial inspection of the vehicle, the dealership found metal shavings in the oil indicating internal engine damage. The manufacture requested my oil change records suggesting that this was my fault. I presented the oil change receipts but they still refused recall coverage and the dealership requested approximately $5,000 for diagnostics, if determined my fault. If it is determined that the defect damaged the engine, they will cover the 5k. After several weeks of inspection and going through the manufacture recall process, the dealership determined the recall issue applies my car. However, due to the engine number not on the “list” they are denying my recall coverage. They are seeking $25k for service repairs. After almost 2 months of back and forth, I have been misled and misinformed. I am struggling to get my car repaired under recall.

The vehicle experienced vibration symptoms and stalled on the road. The day before it stalled, there were rattling noises which prompted me to take the car to the dealership the next day. I had just received the letter about the recall so I knew it was likely related. The car was towed to the Acura dealership but the dealership denied recall coverage, stating the engine number did not match the recall list. During the discovery process, it was later discovered that the engine had been swapped by the dealership in 2018 — a fact that was not disclosed to me at the time of my purchase. The installed engine still falls within the recall defect interval of 2015-2020 but they are resistant to repair. Upon initial inspection of the vehicle, the dealership found metal shavings in the oil indicating internal engine damage. The manufacture requested my oil change records suggesting that this was my fault. I presented the oil change receipts but they still refused recall coverage and the dealership requested approximately $5,000 for diagnostics, if determined my fault. If it is determined that the defect damaged the engine, they will cover the 5k. After several weeks of inspection and going through the manufacture recall process, the dealership determined the recall issue applies my car. However, due to the engine number not on the “list” they are denying my recall coverage. They are seeking $25k for service repairs. After almost 2 months of back and forth, I have been misled and misinformed. I am struggling to get my car repaired under recall.

While performing routine maintenance on my 2018 Acura TLX, I discovered a critical structural failure in the front right (passenger side) lower control arm. The factory weld connecting the stamped steel control arm to the compliance bushing housing has failed and separated. Visual inspection reveals a clear manufacturing defect: there is a significant crater and void in the weld bead, indicative of incomplete fusion or a "start/stop" error during the manufacturing process. This is a latent structural defect, not a stress fracture from mileage or impact. The weld has begun to separate from the housing, leaving a visible gap. Safety Risk: This failure compromises the suspension geometry and structural integrity of the vehicle. If the weld completes its separation while driving, it would result in the control arm detaching from the subframe, leading to immediate loss of steering control, wheel collapse, and a high probability of a collision. Status: No warning lights were illuminated prior to discovery. The vehicle has not been involved in any collisions that would affect this component. The defective part is currently on the vehicle but is available for inspection by NHTSA or manufacturer representatives upon request.

While performing routine maintenance on my 2018 Acura TLX, I discovered a critical structural failure in the front right (passenger side) lower control arm. The factory weld connecting the stamped steel control arm to the compliance bushing housing has failed and separated. Visual inspection reveals a clear manufacturing defect: there is a significant crater and void in the weld bead, indicative of incomplete fusion or a "start/stop" error during the manufacturing process. This is a latent structural defect, not a stress fracture from mileage or impact. The weld has begun to separate from the housing, leaving a visible gap. Safety Risk: This failure compromises the suspension geometry and structural integrity of the vehicle. If the weld completes its separation while driving, it would result in the control arm detaching from the subframe, leading to immediate loss of steering control, wheel collapse, and a high probability of a collision. Status: No warning lights were illuminated prior to discovery. The vehicle has not been involved in any collisions that would affect this component. The defective part is currently on the vehicle but is available for inspection by NHTSA or manufacturer representatives upon request.