2003 HONDA HONDA MOTORCYCLE — Problems, Recalls & Safety Data

THE FRAME IS CRACKED. HONDA HAD A RECALL THAT IS NO LONGER HONORED. HONDA CUSTOMER SERVICE SAID BIKE WAS REPAIRED BUT THERE IS NO EVIDENCE OF THAT OR IT RECRACKED. THIS IS DEFINITELY A SAFETY ISSUE. IT WAS DISCOVERED BY SERVICE ON 9/12/13

THERE ARE CRITICAL NUTS AND BOLTS THAT MUST BE TORQUED TO SPECIFIC MANUFACTURER'S ASSEMBLY SPECIFICATIONS BY ALL HONDA POWERSPORTS DEALERS THAT ARE COMPLETING THE FINAL ASSEMBLY PROCESS FOR AMERICAN HONDA MOTOR COMPANY ON NEW HONDA MOTORCYCLES. IF THESE CRITICAL NUTS AND BOLTS ARE NOT TORQUED TO THE MANUFACTURER'S SPECIFIC SPECIFICATIONS, THEN THEY CAN COME LOOSE IF UNDER TIGHTENED OR THEY CAN COME LOOSE IF OVERTIGHTENED AND THE TREADS STRIP. THIS CAN CAUSE A MALFUNCTION OF THE MOTORCYCLE THUS POSSIBLY CAUSING AN ACCIDENT THAT CAN RESULT IN A SERIOUS INJURY OR DEATH. SOUTHERN HONDA POWERSPORTS IN CHATTANOOGA, TENNESSEE HAS NEVER USED ACTUAL TORQUE WRENCHES (THAT GAUGE THE POUNDS OF PRESSURE APPLIED WHEN TIGHTENING SPECIFIC NUTS AND BOLTS), AS REQUIRED IN THE FINAL ASSEMBLY PROCESS. THESE NUTS AND BOLTS IF NOT TORQUED CORRECTLY TO MANUFACTURER'S SPECIFICATIONS (I.E. TO A SPECIFIC NUMBER OF POUNDS) CAN COME LOOSE THUS CAUSING THE MOTORCYCLE OPERATOR TO LOOSE CONTROL. THIS CRITICAL SAFETY ISSUE AT SOUTHERN HONDA POWERSPORTS HAS BEEN CALLED TO AMERICAN HONDA MOTOR COMPANYS ATTENTION ON MANY OCCASIONS DURING THE LAST 5 YEARS BY A NUMBER OF PEOPLE. EVEN SIGNED, NOTARIZED, SWORN AFFIDAVITS BY INDIVIDUALS THAT HAVE ASSEMBLED NEW HONDA MOTORCYCLES AT SOUTHERN HONDA POWERSPORTS, ATTESTING TO THE ABOVE, HAVE BEEN SUBMITTED TO AMERICAN HONDA MOTOR COMPANY. NHTSA HAS PREVIOUSLY ESTABLISHED A PRECEDENT REQUIRING A SAFETY RECALL FOR THIS IDENTICAL TYPE MOTORCYCLE ASSEMBLY SAFETY ISSUE, BY ISSUING A "SAFETY RECALL" ON VICTORY MOTORCYCLES, NHTSA ID # 12V457000. AS A RESULT OF THE CRITICAL SAFETY CONCERNS ABOVE, AMERICAN HONDA MOTOR COMPANY MUST BE REQUIRED BY NHTSA TO RECALL EVERY IMPROPERLY ASSEMBLED HONDA MOTORCYCLE SOLD BY SOUTHERN HONDA POWERSPORTS, CHATTANOOGA, TN FROM FEBRUARY 2004 THRU CURRENT DATE 2012. *TR . .

TL*THE CONTACT OWNS A 2003 HONDA 900F (NA). WHILE RIDING 20 MPH ON WET ROAD CONDITIONS, THE SHIFTER FELL OFF AND THE CONTACT COULD NOT CHANGE GEARS. THE FAILURE OCCURRED WHILE DRIVING IN SIXTH GEAR. HE WAS INJURED WHILE GETTING OFF OF THE BIKE. THE DEALER STATED THAT THEY WOULD INSPECT THE VEHICLE. THE FAILURE AND CURRENT MILEAGES WERE 2,321.

FINAL DRIVE FLANGE BEARING FAILURE,2003 HONDA VTX 1800 RETRO MODEL MOTORCYCLE, I WAS REPLACING A WORN TIRE AND INSPECTED THE FLANGE BEARINGS,BOTH WERE NO GOOD,BALL BEARINGS AND SEAL MISSING FROM ONE AND THE OTHER DID NOT TURN,MY DEALER REPLACED THEM BOTH UNDER MY EXTENDED WARRANTY. *JB

DT: OWNS A HONDA GOLDWING WHICH HAS BEEN MODIFIED INTO A CONVERSION MOTOR BIKE WHICH TURNED THIS INTO A 3 WHEEL VEHICLE. CONSUMER FELT THERE WAS AN ISSUE WITH THE BRAKES. THE BRAKE PADS DESTROYED THE ROTORS. CONSUMER DID NOT HAVE A SENSOR LIKE THOSE ON A CAR ,BUT THERE WAS ONLY 4-5,000 MILES BEFORE THE ROTOR WERE DESTROYED. BECAUSE HONDA WAS A DUAL BRAKING SYSTEM ,SO IF LOSING THE REAR STILL HAS THE FRONT BRAKES, THE MOTOR BIKE CONVERSION FRONT BRAKES WERE NOT MODIFIED BUT REAR BRAKES WERE CONVERTED. THE DESIGN OF THE SOFT ROTORS WAS A PROBLEM, AND THEY USED A IRON ROTOR WITH A MOTORCYCLE DISC PAD WHICH WAS STRONG AND HARD WHICH DESTROYED THE ROTOR. WHEN THIS OCCURRED THE PADS BEGAN TO WEAR AS WELL. HAS BEEN TO DEALER TO REPLACE ROTORS AND PADS, BUT THEY WERE REPLACED WITH THE SAME DEFECTIVE ROTORS AND PADS. *AK