2017 GMC YUKON XL — Problems, Recalls & Safety Data

Gear slippage, loss of power

The contact owns a 2017 GMC Yukon XL. The contact stated that the check engine warning light was illuminated. The contact stated that while idling, the vehicle started shuddering violently. The contact stated that while driving to the residence at an undisclosed speed, the vehicle stalled and failed to restart. The vehicle was pushed into a church parking lot. The contact's father used a scanner to scan the vehicle, and a DTC for engine misfire was retrieved. The contact's father replaced the spark plugs, but the failure persisted. The vehicle was towed to an independent mechanic, where it was diagnosed and determined that the engine was blown. The vehicle was then towed to another independent mechanic, where the engine was replaced. Additionally, the contact stated that upon depressing the brake pedal, the brake pedal was stiff and required to be pumped several times for the vehicle to respond as intended. The contact stated that the failure occurred while starting the vehicle and while driving at various speeds. There was no warning light illuminated. The contact stated that the brakes had been replaced annually, but the failure persisted. The contact stated that the brake pedal shuddered upon starting the vehicle. The contact received a notification for ABS from the OnStar Mobile App. The vehicle was not repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 148,246.

The contact owns a 2017 GMC Yukon XL. The contact stated that the check engine warning light was illuminated. The contact stated that while idling, the vehicle started shuddering violently. The contact stated that while driving to the residence at an undisclosed speed, the vehicle stalled and failed to restart. The vehicle was pushed into a church parking lot. The contact's father used a scanner to scan the vehicle, and a DTC for engine misfire was retrieved. The contact's father replaced the spark plugs, but the failure persisted. The vehicle was towed to an independent mechanic, where it was diagnosed and determined that the engine was blown. The vehicle was then towed to another independent mechanic, where the engine was replaced. Additionally, the contact stated that upon depressing the brake pedal, the brake pedal was stiff and required to be pumped several times for the vehicle to respond as intended. The contact stated that the failure occurred while starting the vehicle and while driving at various speeds. There was no warning light illuminated. The contact stated that the brakes had been replaced annually, but the failure persisted. The contact stated that the brake pedal shuddered upon starting the vehicle. The contact received a notification for ABS from the OnStar Mobile App. The vehicle was not repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 148,246.

On July 3, 2025 we were traveling on a 4 lane at 55mph. Without any prior symptoms, the vehicle began to shake violently. It shook so hard that the skid warning light simultaneously came on. It was followed by the check engine light. The oil pressure guage started bouncing around. We stopped driving the vehicle and had it towed to VanYork GMC dealer in Asheboro, NC on this same day. (Invoice attached) VanYork GMC determined that cyclinder 5 was misfiring. We paid to have them repair it, and we began driving the vehicle again. (invoice attached) On or about August 1, 2025 we were traveling on an interstate at 70mph. Without any forewarning, the vehicle began to violently shake. Just as before, the skid warning light simultaneously came on, followed by the check engine light came on, and then the oil pressure guage started bouncing around. As there was heavy traffic on the interstate, the failure created a very dangerous situation for us as we tried to maintain our lane, and stay in control of the vehicle until which time we were able to safely maneuver to the side of the road. The vehicle was again towed to Vann York GMC in Asheboro, NC. (invoice attached) On December 3, 2025 we received a call from VannYork GMC saying that the vehicle repairs were complete. It had been in their repair shop for 4 months. This repair began with lifter and camshaft replacement. When this repair was unsuccessful, they decided that the vehicle needed a 'new' rebuilt engine. Since GMC has not offered any assistance with the expense of this new re-built engine, we will have to satisfy the $12,000 bill when we pick it up. After experiencing two very dangerous episodes, we are happy that we did not wreck, but certainly, this not the situation we expected from a high-end vehicle with only 76,169 miles on it.

At stop light vehicle began to sputter and make noise, I was very close to my home, no engine light on. Upon turning vehicle off and using a code reader codes P0106 and P0506 was on scanner. I had vehicle towed to Complete Car Care. Mis fire on multiple cylinders. Vehicle has 69,801 miles. 3 push rods bent and I valve spring broken. The right Cylinder head assembly had to be removed and replaced with 8 new push rods, 8 new lifters, gaskets, seals, and valve spring. Cost was $3304.79. In addition the rear tail light has been sporadic on and off, GM was to replace up to 70,000 miles. When I took it to them they stated the time limit had expired, yet I had not been informed until I did a google search. GM requesting $475 plus tax. I am concerned my vehicle has the same manufacturing defects as the GM motors being recalled with total engine failures.